Quick Installation the Tp-Link TL-WR1043ND Wireless N Gigabit Router — TCP/IP Configuration

Category : TL-WR1043ND

This chapter will show you how to configure the basic functions of your TL-WR1043ND Wireless N Gigabit Router using Quick Setup Wizard within minutes.

TCP/IP Configuration

The default domain name of the Tp-Link TL-WR1043ND Wireless N Gigabit Router is http://tplinklogin.net,

the default IP address is 192.168.1.1, and the default Subnet Mask is 255.255.255.0.

These values can be changed as you desire. In this guide, we all use the default values for description.

Connect the local PC to the LAN ports of the Router, and then you can configure the IP address for your PC by following the steps below:

1) Set up the TCP/IP Protocol in “Obtain an IP address automatically” mode on your PC.
If you need instructions as to how to do this, please refer to “Configuring the PC

2) Then the built-in DHCP server will assign IP address for the PC.

Now, you can run the Ping command in the command prompt to verify the network connection between your PC and the Router.

The following example is in Windows 2000 OS.

Open a command prompt, and type ping 192.168.1.1, and then press Enter.

Continue Reading


How to Connect to the Tp-Link TL-WR1043ND Wireless N Gigabit Router

Category : TL-WR1043ND

1 System Requirements

  • Broadband Internet Access Service (DSL/Cable/Ethernet)
  • One DSL/Cable Modem that has an RJ45 connector (which is not necessary if the Router is connected directly to the Ethernet.)
  • PCs with a working Ethernet Adapter and an Ethernet cable with RJ45 connectors
  • TCP/IP protocol on each PC
  • Web browser, such as Microsoft Internet Explorer 5.0 , Netscape Navigator 6.0 or above

2 Installation Environment Requirements

  • Place the Router in a well ventilated place far from any heater or heating vent
  • Avoid direct irradiation of any strong light (such as sunlight)
  • Keep at least 2 inches (5 cm) of clear space around the Router
  • Operating Temperature: 0℃~40℃ (32℉~104℉)
  • Operating Humidity: 10%~90%RH, Non-condensing

Continue Reading


TP-LINK TL-WR1043ND Wireless N Gigabit Router Main Features

Category : TL-WR1043ND

The TL-WR1043ND Wireless N Gigabit Router integrates 4-port Switch, Firewall, NAT-Router and Wireless AP.

The Wireless N Gigabit Router delivers exceptional range and speed,

which can fully meet the need of Small Office/Home Office (SOHO) networks and the users demanding higher networking performance.

The Router or TL-WR1043ND mentioned in this guide stands for TL-WR1043ND Wireless N Gigabit Router without any explanation.

Main Features

Complies with IEEE 802.11n to provide a wireless data rate of up to 300Mbps.

One 10/100/1000M Auto-Negotiation RJ45 WAN port, four 10/100/1000M Auto-Negotiation RJ45 LAN ports, supporting Auto MDI/MDIX.

Provides WPA/WPA2, WPA-PSK/WPA2-PSK authentication, TKIP/AES encryption security.

Shares data and Internet access for users, supporting Dynamic IP/Static IP/PPPoE Internet access.

Supports Virtual Server, Special Application and DMZ host.

Supports UPnP, Dynamic DNS, Static Routing.

Provides Automatic-connection and Scheduled Connection on certain time to the Internet

Built-in NAT and DHCP server supporting static IP address distributing.

Supports Parental Control and Access Control.

Connects Internet on demand and disconnects from the Internet when idle for PPPoE.

Provides 64/128/152-bit WEP encryption security and wireless LAN ACL (Access Control List).

Supports Flow Statistics.

Supports firmware upgrade and Web management.


TP-Link TL-MR3420 Router with 3G and Wi-Fi 802.11n — Quick Setup Capabilities Part 2

1

Category : TL-MR3420

Built-in DHCP-server allows you to view the current list of connected PCs, but at the same time set the bind IP addresses to MAC.

Tp-Link DHCP

Tp-Link DHCP Clients List

Continue Reading


TP-Link TL-MR3420 Router with 3G and Wi-Fi 802.11n — Introduction

Category : TL-MR3420

Introduction

TP-Link TL-MR3420 differs from many of his fellow 3G-enabled modems.

Just in case, when the main provider has stopped working, and the Internet very well, like.

This feature is relevant and summer, during the summer season.

In addition, the TL-MR3420 is not very expensive, and full Wi-Fi 802.11n support

TP-Link TL-MR3420 primarily interested in the fact that it supports not only the usual wired WAN-connection,

but also 3G-modem. Thus, the connection to the network can be used as a backup channel for access

to the Internet in those moments when the main ISP suddenly decides to conduct maintenance work or simply “fall.”

This possibility is useful for organizing wireless network in the country, where the wired network is generally absent.

Looking ahead to say that TP-Link TL-MR3420 – it’s pretty good solution for small office or a particularly fastidious users,

who need to always be online. If the “fall” in the main channel network, it will automatically be picked up 3G-connection.

However, the opposite situation is possible when the mobile Internet is used as the core, and a wired connection will be waiting in the wings.

However, we must recognize that the TP-Link TL-MR3420 has some, well, strange and quite obvious shortcomings.

Look at the possibilities of a TP-Link Router in more detail.

Continue Reading


TP-Link TL-MR3420 Router with 3G and Wi-Fi 802.11n — Quick Setup Capabilities

1

Category : TL-MR3420

Web-based interface, as well as opportunities and TP-Link TL-MR3420 also largely similar to other models of functional router TP-Link.

IP-address defaults to 192.168.1.1, and login and password for admin.

Left in the interface is the main menu displayed in the center of adjustable parameters,

and to the right shows a little help on him. Unfortunately,

the translation of web-based interface to Russian language in the TP-Link has not yet been attended to.

The default home page appears with basic information about the state of the router,

the status of current connections, the volume of data transferred and so on.

Tp-Link Quick Setup

Continue Reading


Why I can not connect TP-Link TL-WR741ND to my AP via wireless by using WDS?

1

Category : TP-Link Wireless

  • Does the main AP support WDS (4 MAC address data frame)?
  • The WDS function using 4 MAC address data frame ( Which called WDS feature),
    so it need the AP also using 4 MAC address when sending/receiving
    data
  • This issue is the same on other 11N tp-link wireless router

What is the different of WDS between TP-Link 11n device and 11b/g device?

Category : TP-Link Wireless

WDS – Wireless Distribution System
It defines connecting the TP-LINK wireless device via wireless, such as connect two wireless routers or Access Points via wireless.
And for this proposal it need the devices support Four MAC address Frame.
We also call this as WDS (technology).

  • For TP-LINK 11b/g router and Access Point, and 11n Access Point
    They support WDS (technology), and we can use Bridge mode or Repeater mode to connect two wireless routers or Access Points together via wireless
  • For TP-LINK 11n router
    Support WDS (technology), and we can use the WDS function to connect the router to another one via wireless.
    In fact, this WDS function is AP+APC mode, just we call it WDS function,
    because it is a method of connecting two wireless device according to the WDS technology
    And Please also note, this WDS function only can connect to the TP-LINK wireless device which support WDS (technology)