Tp-Link TL-WA5210G 2.4GHz High Power Wireless Outdoor CPE Operation Mode

Category : TL-WA5210G

Selecting Operation Mode will allow you to choose the operation mode for the AP.

The AP supports three operation mode types, AP Client Router, AP Router and AP.

Please select the one your want as shown in Figure. Click Save to save your choice.

Operation Mode

AP Client Router – In this mode, the device enables multi-user to share the Internet from WISP.
All LAN ports share the same IP from WISP through Wireless port.
While connecting to WISP, the Wireless port works as a WAN port in AP Client mode.
The Ethernet port acts as a LAN port.

AP Router – In this mode, the device enables multi-user to share the Internet via ADSL/Cable Modem.
The wireless port share the same IP to ISP through Ethernet WAN port.
The Wireless port acts same as a LAN port while in AP mode.

AP – In this mode, the device allows wireless communication devices to access a wireless network by using WIFI.
The Ethernet port and the wireless port both work as LAN ports.


Tp-Link TL-WA5210G 2.4GHz High Power Wireless Outdoor CPE Status Overview

Category : TL-WA5210G

Selecting Status will enable you to view the AP’s current status and configuration, all of which is read-only.

Status

1. LAN
This field displays the current settings or information for the LAN, including the MAC address, IP address and Subnet Mask.

2. Wireless
This field displays basic information or status for wireless function, including Wireless Radio, SSID, Channel, Mode, and Wireless MAC address.

3. WAN
These parameters apply to the WAN port of the router, including MAC address, IP address, Subnet Mask, Default Gateway and DNS server.

If PPPoE is chosen as the WAN connection type, the Disconnect button will be shown here while you are accessing the Internet.

You can also cut the connection by clicking the button.

If you have not connected to the Internet, just click Connect to establish the connection.

4. Traffic Statistics
This field displays the router’s traffic statistics.

5. System Up Time
The total up time of the router since it was powered on or reset.


Tp-Link TL-WA5210G 2.4GHz High Power Wireless Outdoor CPE Configure the Device

1

Category : TL-WA5210G

The instructions in this section will help you configure each of your PCs to be able to communicate with the AP.

The default IP address of the TL-WA5210G 2.4GHz High Power Wireless Outdoor CPE is 192.168.1.254.

And the default Subnet Mask is 255.255.255.0. These values can be seen from the LAN.

They can be changed as you desire, as an example we use the default values for description in this guide.

Connect the local PC to the LAN ports of the AP. There are then two ways to configure the IP address for your PC.

Configure the IP address manually

1) Set up the TCP/IP Protocol for your PC.
If you need instructions as to how to do this, please refer to 2Appendix B: Configuring the PC

2) Configure the network parameters.
The IP address is 192.168.1.xxx (“xxx” is from 1 to 253), Subnet Mask is 255.255.255.0, and Gateway is 192.168.1.254 (The AP’s default IP address)

Obtain an IP address automatically
Continue Reading


Tp-Link TL-WA5210G 2.4GHz High Power Wireless Outdoor CPE Hardware Installation — Interfaces and button

Category : TL-WA5210G

Rear Panel sketch

View from left to right, the parts are explained below.

power: This is where you can connect an outside antenna.
For this AP, the antenna is built inside, and usually there is not necessary to connect an outside one.

LAN: This port is used to connect to the POE port of the provided Power Injector.

RESET:
There are two ways to reset the AP’s factory defaults:
• Use the Factory Defaults function on System Tools -> Factory Defaults page in the AP’s Web-based Utility.
• Use the Factory Default Reset button: Press and hold the RESET button for at least 5
seconds, and then the AP reboots after the LED at the rightmost in Figure flashes.

Note:
Ensure the AP is powered on before it restarts completely.


Tp-Link TL-WA5210G 2.4GHz High Power Wireless Outdoor CPE Hardware Installation — LED Explanation

Category : TL-WA5210G

TL-WA5210G consists of several LED indicators, which is designed to indicate connections and Wireless Signal.

Front Panel sketch

View from left to right.

Wireless Signal Strength

Note:
For Wireless Signal Strength LEDs:
In AP or Bridge mode, all the four LEDs will light up.
In Client or Repeater mode, the corresponding LED(s) will light up when the RSSI value (wireless signal strength value) reaches the RSSI Threshold. The value of RSSI Threshold can be set on Wireless Advanced Settings page as shown in Figure.

For example, if the RSSI value is 30, the RSSI Threshold of the four LED are 15, 25, 35, 45 respectively, and then the LEDs whose RSSI Threshold are 15 and 25 will light up.


Tp-Link TL-WA5210G 2.4GHz High Power Wireless Outdoor CPE Features

Category : TL-WA5210G

Complies with IEEE 802.11g, IEEE 802.11b, IEEE 802.3, IEEE 802.3u standards.

Wireless Data transfer rates up to 54Mbps.

Supports AP Client Router, AP Router and AP operation mode.

High output transmit power and receive sensitivity optimized.

Supports Client Router Mode for WISP CPE

Supports passive power over Ethernet.

Supports Wireless Distribution System (WDS).

ACK timeout adjustment for long range transmission, up to 50km.

Supports Antenna Alignment.

Provides throughput monitor indicating the current wireless throughput.

Supports Layer 2 User Isolation.

Supports Ping Watch Dog.

Supports link speed test.

Supports Remote Management

Output transmit power adjustable.

Supports PPPoE, Dynamic IP, Static IP Internet Access.

Built-in NAT and DHCP server supporting static IP address distributing.

Supports UPnP, Dynamic DNS, Static Routing, VPN Pass-through.

Supports Virtual Server, Special Application and DMZ host.

Built-in firewall supporting IP address filtering, Domain Name filtering, and MAC address filtering.

Provides WLAN ACL (Access Control List).

Supports configuration backup/restore and firmware upgrade.

Supports Web management.


Tp-Link TL-WA5210G 2.4GHz High Power Wireless Outdoor CPE Overview of the Product

Category : TL-WA5210G

The Tp-Link TL-WA5210G 2.4GHz High Power Wireless Outdoor CPE is dedicated to Outdoor wireless network solutions.

The Tp-Link TL-WA5210G 2.4GHz High Power Wireless Outdoor CPE will allow you to connect your network with other wireless devices wirelessly, sharing Internet Access, files and fun, easily and securely. The high power design will also help you build a more stable link or cover more area outdoors.

The Tp-Link TL-WA5210G 2.4GHz High Power Wireless Outdoor CPE provides 3 operation modes for multi-user to access the Internet: AP client router, AP router and AP.

In AP client router mode, it works as a WISP CPE and can access the Internet wirelessly via your WISP.

In AP router mode, it can access the Internet via an ADSL/Cable Modem, while sharing data wirelessly.

In AP mode it can work in various modes, such as Access Point/Client/WDS Bridge/Repeater.

With the most attentive wireless security, the Tp-Link TL-WA5210G 2.4GHz High Power Wireless Outdoor CPE provides multiple protection measures.

It can be set to turn off wireless network name (SSID) broadcast so that only stations that have the SSID can be connected.

The AP provides wireless LAN 64/128/152-bit WEP encryption security, and WPA/WPA2 and WPA-PSK/WPA2-PSK authentication, as well as TKIP/AES encryption security.

It also supports VPN pass-through for sensitive data secure transmission.

The Tp-Link TL-WA5210G 2.4GHz High Power Wireless Outdoor CPE complies with the IEEE 802.11g and IEEE 802.11b standards so that the data transmission rate is up to 54Mbps.

The wireless transmission range can extend up to tens of kilometers.