TP-LINK TL-WA901ND 300Mbps Wireless N Access Point DHCP Settings

Category : TL-WA901ND

Selecting DHCP > DHCP Settings will enable you to set up the AP as a DHCP (Dynamic Host Configuration Protocol) server, which provides the TCP/IP configuration for all the PCs that are connected to the system on the LAN.
The DHCP Server can be configured on the page.

Tp-link TL-WA901ND DHCP Settings

DHCP Server – Selecting the radio button before Disable/Enable will disable/enable the DHCP server on your AP.
The default setting is Disable.
If you disable the Server, you must have another DHCP server within your network or else you must manually configure the computer.

Start IP Address – This field specifies the first address in the IP Address pool. 192.168.1.100 is the default start IP address.

End IP Address – This field specifies the last address in the IP Address pool. 192.168.1.199 is the default end IP address.

Address Lease Time – Enter the amount of time for the PC to connect to the AP with its current assigned dynamic IP address.
The time is measured in minutes. After the time is up, the PC will be automatically assigned a new dynamic IP address.
The range of the time is 1 ~ 2880 minutes. The default value is 120 minutes.

Continue Reading


TP-LINK TL-WR700N 150Mbps Wireless N Mini Pocket Router DHCP Settings for Client Mode

Category : TL-WR700N

Choose menu “DHCP → DHCP Settings”, and then you can configure the DHCP Server on the page as shown in Figure. The Router is set up by default as a DHCP (Dynamic Host Configuration Protocol) server, which provides the TCP/IP configuration for all the PC(s) that are connected to the Router in the LAN.

Client Mode DHCP Settings

DHCP Server – Enable or Disable the DHCP server.
If you disable the Server, you must have another DHCP server within your network or else you must configure the computer manually.

Continue Reading


TP-LINK TL-WR700N 150Mbps Wireless N Mini Pocket Router DHCP Settings for Bridge Mode

Category : TL-WR700N

Choose menu “DHCP → DHCP Settings”, and then you can configure the DHCP Server on the page as shown in Figure. The Router is set up by default as a DHCP (Dynamic Host Configuration Protocol) server, which provides the TCP/IP configuration for all the PC(s) that are connected to the Router in the LAN.

DHCP Server – Enable or Disable the DHCP server.
If you disable the Server, you must have another DHCP server within your network or else you must configure the computer manually.

Continue Reading


TP-LINK TL-WR700N 150Mbps Wireless N Mini Pocket Router DHCP Settings

Category : TL-WR700N

Choose menu “DHCP → DHCP Settings”, and then you can configure the DHCP Server on the page as shown in Figure.
The Router is set up by default as a DHCP (Dynamic Host Configuration Protocol) server, which provides the TCP/IP configuration for all the PC(s) that are connected to the Router on the LAN.

DHCP Server – Enable or Disable the DHCP server. If you disable the Server, you must have another DHCP server within your network or else you must configure the computer manually.

Start IP Address – Specify an IP address for the DHCP Server to start with when assigning IP addresses. 192.168.0.100 is the default start address.

Continue Reading


TP-Link TL-WR2543ND 450Mbps Dual-Band Wireless N Gigabit Router DHCP Settings

Category : TL-WR2543ND

Choose menu “DHCP → DHCP Settings“, you can configure the DHCP Server on the page as shown in Figure .

The Router is set up by default as a DHCP (Dynamic Host Configuration Protocol) server, which provides the TCP/IP configuration for all the PC(s) that are connected to the Router on the LAN.

DHCP Settings.png

DHCP ServerEnable or Disable the DHCP server. If you disable the Server, you must have another DHCP server within your network or else you must configure the computer manually.

Start IP Address – Specify an IP address for the DHCP Server to start with when assigning IP addresses. 192.168.0.100 is the default start address.

Continue Reading


Tp-Link TL-WA5210G 2.4GHz High Power Wireless Outdoor CPE DHCP Settings

Category : TL-WA5210G

Selecting DHCP > DHCP Settings will enable you to set up the AP as a DHCP (Dynamic Host Configuration Protocol) server, which provides the TCP/IP configuration for all the PCs that are connected to the system on the LAN.

The DHCP Server can be configured on the page.

DHCP Settings

DHCP Server – Selecting the radio button before Disable/Enable will disable/enable the DHCP server on your AP.
The default setting is Disable. If you disable the Server, you must have another DHCP server within your network or else you must manually configure the computer.

Continue Reading


TP-Link TL-WA500G 54M Wireless Access Point DHCP Settings

Category : TL-WA500G

DHCP stands for Dynamic Host Configuration Protocol. The DHCP Server will automatically assign dynamic IP addresses to the computers on the network.

This protocol simplifies network management and allows new wireless devices to receive IP addresses automatically without the need to manually assign new IP addresses.

There are three submenus under the DHCP menu (shown as Figure): DHCP Settings, DHCP Clients List and Address Reservation.

Clicking any of them will enable you to configure the corresponding function. The detailed explanations for each submenu are provided below.

Selecting DHCP > DHCP Settings will enable you to set up the AP as a DHCP (Dynamic Host Configuration Protocol) server, which provides the TCP/IP configuration for all the PCs that are connected to the system on the LAN. The DHCP Server can be configured on the page

Tp-link DHCP Settings

DHCP Server – Selecting the radio button before Disable/Enable will disable/enable the DHCP server on your AP. The default setting is Disable. If you disable the Server, you must have another DHCP server within your network or else you must manually configure the computer.

Start IP Address – Enter an IP address for the DHCP Server to start with when assigning IP addresses. 192.168.1.100 is the default start IP address.

End IP Address – Enter an IP address for the DHCP Server to end with when assigning IP addresses. 192.168.1.199 is the default end address.

Continue Reading


Tp-Link TL-WR1043ND Wireless N Gigabit Router Wireless DHCP Settings

Category : TL-WR1043ND

There are three submenus under the DHCP menu : DHCP Settings, DHCP Clients List and Address Reservation.

Click any of them, and you will be able to configure the corresponding function.

Choose menu “DHCP→DHCP Settings”, and then you can configure the DHCP Server on the page .

The Router is set up by default as a DHCP (Dynamic Host Configuration Protocol) server, which provides the TCP/IP configuration for all the PC(s) that are connected to the Router on the LAN.

DHCP Settings

DHCP Server - Enable or Disable the DHCP server. If you disable the Server, you must have another DHCP server within your network or else you must configure the computer manually.

Start IP Address – Specify an IP address for the DHCP Server to start with when assigning IP addresses.
192.168.1.100 is the default start address.

End IP Address – Specify an IP address for the DHCP Server to end with when assigning IP addresses.
192.168.1.199 is the default end address.

Address Lease Time – The Address Lease Time is the amount of time a network user will be allowed connection to the Router with their current dynamic IP Address. Enter the amount of time in minutes and the user will be “leased” this dynamic IP Address.
After the time is up, the user will be automatically assigned a new dynamic IP address.
The range of the time is 1 ~ 2880 minutes. The default value is 120 minutes.

Default Gateway – (Optional.) Suggest to input the IP address of the LAN port of the Router, default value is 192.168.1.1

Default Domain – (Optional.) Input the domain name of your network.

Primary DNS – (Optional.) Input the DNS IP address provided by your ISP. Or consult your ISP.

Secondary DNS – (Optional.) Input the IP address of another DNS server if your ISP provides two DNS servers.

Note:
To use the DHCP server function of the Router, you must configure all computers on the LAN as “Obtain an IP Address automatically” mode.