TP-Link TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router Advanced Configuration

Category : TD-W8960N

Choose “Wireless”->”Advanced, you will see the screen of Wireless–Advanced settings shown as below.

Tp-link Advanced

Channel: Select the channel you want to use from the drop-down List.
This field determines which operating frequency will be used.
It is not necessary to change the wireless channel unless you notice interference problems with another nearby access point.
Continue Reading


TP-Link TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router MAC Filter Configuration

Category : TD-W8960N

Choose “Wireless”->”MAC Filter, you will see the screen of Wireless–MAC Filter settings shown as below.

Wireless--MAC Filter

Wireless access can be filtered by using the MAC addresses of the wireless devices transmitting within your network’s RADIUS.

To filter wireless users by MAC Address, either permitting or blocking access.

If you do not wish to filter users by MAC Address, select Disabled.

Disabled: Select this option to disable MAC Filter function.

Allow: Select this option to enable MAC Filter function that allow wireless access by the devices listed on this screen.

Deny: Select this option to enable MAC Filter function that block wireless access from the devices listed on this screen.

Add: Click this button to add the MAC Address.

Remove: Select the item of the MAC Address and click this button to remove it.

Continue Reading


TP-Link TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router Manual Setup AP – WPA2-PSK and Mixed WPA2/WPA and Mixed WPA2/WPA-PSK

Category : TD-W8960N

5. WPA2-PSK

To configure WPA2-PSK settings, select the WPA2-PSK option from the drop-down list.
The menu will change to offer the appropriate settings.
WPA2-PSK requires a shared key and does not use a separate server for authentication.
PSK keys can be ASCII or Hex type.

WPA2-PSK Manual Setup AP

Continue Reading


TP-Link TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router Manual Setup AP – WPA-PSK and WPA2

Category : TD-W8960N

3.WPA-PSK

WPA-PSK requires a shared key and does not use a separate server for authentication. PSK keys can be ASCII or Hex type.

WPA-PSK Manual Setup AP

Continue Reading


TP-Link TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router Manual Setup AP – WEP and WPA

Category : TD-W8960N

Follow the instructions below to configure security features of the wireless LAN interface manually.
You can set the network authentication method, select data encryption, specify whether a network key is required to authenticate to this wireless network and specify the encryption strength.

Tp-link Wireless Security

Continue Reading


TP-Link TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router Wireless QSS(WPS) Setup

Category : TD-W8960N

Choose “Wireless”->”Security”, you will see the screen of Wireless–Security settings shown as below.

You can configure security features of the wireless LAN interface by manually setting the network authentication or through QSS (Quick Security Setup) method.

Tp-Link Wireless Security

Continue Reading


TP-Link TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router Wireless Basic Configuration

Category : TD-W8960N

Choose “Wireless”->”Basic”, you will see the screen of Wireless–Basic settings shown as below.

The basic settings for wireless networking are set on this screen.

Tp-link Wireless Basic

This page allows you to configure basic features of the wireless LAN interface.

You can enable or disable the wireless LAN interface, hide the network from active scans, set the wireless network name (also known as SSID) and restrict the channel set based on Region requirements.

Continue Reading


TP-Link TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router IPSec Configuration

1

Category : TD-W8960N

Choose “Advanced Setup”->“IPSec, you can Add/Remove or Enable/Disable the IPSec tunnel connections on the screen as shown in Figure

IPSec Tunnel Mode Connections

This section will guide you to configure a VPN tunnel between two TD-W8960Ns. The topology is as follows.

Continue Reading